pa ckage schematic 6/15/05 p age 1 of 10 ?2005 fairchild semiconductor corporation 6-pin dip zero-cross phototriac driver optocoupler (600v peak) MOC3061-M moc3062-m moc3063-m moc3162-m moc3163-m description the moc306x-m and moc316x-m devices consist of a gaas infrared emitting diode optically coupled to a monolithic silicon detector performing the function of a zero voltage crossing bilateral triac driver. they are designed for use with a triac in t he inter- f ace of logic systems to equipment powered from 115/240 vac lines, such as solid-state relays, industrial controls, motors, sol e- noids and consumer appliances, etc. features simpli?s logic control of 115/240 vac power zero voltage crossing dv/dt of 1000 v/? guaranteed (moc316x-m), 600 v/? guaranteed (moc306x-m) vde recognized (file # 94766) ordering option v (e.g., moc3063v-m) underwriters laboratories (ul) recognized (file #e90700, volume 2) applications solenoid/valve controls static power switches ? emperature controls ? c motor starters lighting controls ? c motor drives e.m. contactors solid state relays 6 1 6 6 1 1 main term. nc* n/c *do not connect (triac substrate) 1 2 3 anode cathode 4 5 6 main term. zero crossing circuit
6/15/05 p age 2 of 10 ?2005 fairchild semiconductor corporation 6-pin dip zero-cross phototriac driver optocoupler (600v peak) MOC3061-M moc3062-m moc3063-m moc3162-m moc3163-m absolute maximum ratings (t a = 25? unless otherwise noted) p arameters symbol device value units tot al device storage temperature t stg all -40 to +150 ? operating temperature t opr all -40 to +85 ? lead solder temperature t sol all 260 for 10 sec ? j unction temperature range t j all -40 to +100 ? isolation surge voltage (4) (peak ac voltage, 60hz, 1 sec duration) v iso all 7500 vac(pk) t otal device power dissipation @ 25? p d all 250 mw derate above 25? 2.94 mw/? emitter continuous forward current i f all 60 ma reverse voltage v r all 6 v t otal power dissipation 25? ambient p d all 120 mw derate above 25? 1.41 mw/? detector off-state output terminal voltage v drm all 600 v p eak repetitive surge current (pw = 100 ?, 120 pps) i tsm all 1 a t otal power dissipation @ 25? ambient p d all 150 mw derate above 25? 1.76 mw/?
6/15/05 p age 3 of 10 ?2005 fairchild semiconductor corporation 6-pin dip zero-cross phototriac driver optocoupler (600v peak) MOC3061-M moc3062-m moc3063-m moc3162-m moc3163-m *typical values at t a = 25? notes 1. test voltage must be applied within dv/dt rating. 2. all devices are guaranteed to trigger at an i f value less than or equal to max i ft . therefore, recommended operating i f lies between max i ft (15 ma for MOC3061-M, 10 ma for moc3062-m & moc3162-m, 5 ma for moc3063-m & moc3163-m) and absolute max i f (60 ma). 3. this is static dv/dt. see figure 9 for test circuit. commutating dv/dt is a function of the load-driving thyristor(s) only. 4. isolation surge voltage, v iso , is an internal device dielectric breakdown rating. for this test, pins 1 and 2 are common, and pins 4, 5 and 6 are common. electrical characteristics (ta = 25? unless otherwise speci?d) individual component characteristics p arameters test conditions symbol device min typ* max units emitter input forward voltage i f = 30 ma v f all 1.3 1.5 v reverse leakage current v r = 6 v i r all 0.005 100 ? detector p eak blocking current, either direction v drm = 600v, i f = 0 (note 1) i drm1 moc316x-m 10 100 na moc306x-m 10 500 critical rate of rise of off-state voltage i f = 0 (?ure 9, note 3) dv/dt moc306x-m 600 1500 v/? moc316x-m 1000 transfer characteristics (t a = 25? unless otherwise speci?d.) dc characteristics test conditions symbol device min typ* max units led trigger current (rated i ft ) main terminal v oltage = 3v (note 2) i ft MOC3061-M 15 ma moc3062-m/ moc3162-m 10 moc3063-m/ moc3163-m 5 p eak on-state voltage, either direction i tm = 100 ma peak, i f = rated i ft v tm all 1.8 3 v holding current, either direction i h all 500 ? zero crossing characteristics characteristics test conditions symbol device min typ* max units inhibit voltage (mt1-mt2 voltage above which device will not trigger) i f = rated i ft v inh MOC3061-M/2m/3m 12 20 v moc3162-m/3m 12 15 leakage in inhibited state i f = rated i ft , v drm = 600v, off state i drm2 all 150 500 ? isolation characteristics characteristics test conditions symbol device min typ* max units isolation voltage f = 60 hz, t = 1 sec v iso all 7500 v
6/15/05 p age 4 of 10 ?2005 fairchild semiconductor corporation 6-pin dip zero-cross phototriac driver optocoupler (600v peak) MOC3061-M moc3062-m moc3063-m moc3162-m moc3163-m figure 1. led forward voltage vs. forward current figure 3. led current required to trigger vs. led pulse width figure 4. leakage current, i drm vs. temperature figure 2. trigger current vs. temperature i f , led forward current (ma) 0.1 1 10 100 v f , forward voltage (v) 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 t a , ambient temperature ( c) -40 -20 0 20 40 60 80 100 t a , ambient temperature ( c) -40 -20 0 20 40 60 80 100 i ft , normalized i drm , leakage current (na) 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 pw in , led trigger pulse width ( s) 10 1 100 i ft , led trigger current (normalized) 0 2 4 6 8 10 12 14 16 0.1 1 10 100 1000 10000 t a = -40 c v tm = 3v normalized to t a = 25 c t a = 25 c normalized to pw in >> 100 s t a = 25 c t a = 85 c
6/15/05 p age 5 of 10 ?2005 fairchild semiconductor corporation 6-pin dip zero-cross phototriac driver optocoupler (600v peak) MOC3061-M moc3062-m moc3063-m moc3162-m moc3163-m figure 5. i drm2 , leakage in inhibit state vs. temperature figure 7. i h , holding current vs. temperature figure 8. inhibit voltage vs. temperature figure 6. on-state characteristics v tm , on-state voltage (volts) t a , ambient temperature ( c) -40 -20 0 20 40 60 80 100 t a , ambient temperature ( c) -40 -20 0 20 40 60 80 100 t a , ambient temperature ( c) -40 -20 0 20 40 60 80 100 i drm2 , normalized v inh , normalized i h , holding current (normalized) 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 i f = rated i ft normalized to t a = 25 c -4 -3 -2 -1 0 1 2 3 4 i tm , on-state current (ma) t a = 25 c -800 -600 -400 -200 0 200 400 600 800 0.0 0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2 0.80 0.85 0.90 0.95 1.00 1.05 1.10 1.15 1.20 normalized to t a = 25 c
6/15/05 p age 6 of 10 ?2005 fairchild semiconductor corporation 6-pin dip zero-cross phototriac driver optocoupler (600v peak) MOC3061-M moc3062-m moc3063-m moc3162-m moc3163-m 1. 100x scope probes are used, to allow high speeds and voltages. 2. the worst-case condition for static dv/dt is established by triggering the d.u.t. with a normal led input current, then remo ving the current. the variable vernier resistor combined with various capacitor combinations allows the dv/dt to be gradually increased until the d.u.t. continues to trigger in response to the applied voltage pulse, even after the led current has been removed. the dv/dt is then decreased until the d.u.t. stops triggering. rc is measured at this point and recorded. b asic applications t ypical circuit for use when hot line switching is required. in this circuit the "hot" side of the line is switched and the load connected to the cold or neutral side. the load may be connected to either the neutral or hot line. r in is calculated so that i f is equal to the rated i ft of the part, 15 ma for the MOC3061-M, 10 ma for the moc3062-m, or 5 ma for the moc3063-m. the 39 ohm resistor and 0.01 ? capacitor are f or snubbing of the triac and is often, but not always, necessary depending upon the particular triac and load used. suggested method of ?ing two, back-to-back scr s with a fairchild triac driver. diodes can be 1n4001; resistors, r1 and r2, are optional 330 ohm. note: this optoisolator should not be used to drive a load directly. it is intended to be a trigger device only. 27 2w 2w 100 2w dv dt vernier mount dut on temperature controlled c plate differential preamp f = 10 hz pw = 100 s 50 ? pulse generator all components are non-inductive unless shown 82 2w 470pf 0.001 0.005 0.01 0.047 0.47 0.1 56 2w 1n914 20v 1000 1/4w 1n967a 18v rfp4n100 dut 20k x100 probe x100 probe v drm /v rrm select 6 4 1 2 1000 10 watt wirewound 0.33 1000v power 1 meg 2w each 1.2 meg 2w test 0-1000v 10ma 0.047 1000v figure 9. circuit for static dv measurement of power thyristors dt figure 10. hot-line switching application circuit 0.01 f v cc r in 1 2 3 6 5 4 240 vac hot neutral 360 ? 360 MOC3061-M moc3062-m moc3063-m 39 ? fkpf12n60 load figure 11. inverse-parallel scr driver circuit v cc r in 1 2 3 6 5 4 115 vac scr 360 ? r1 d1 scr MOC3061-M moc3062-m moc3063-m r2 d2 load
6/15/05 p age 7 of 10 ?2005 fairchild semiconductor corporation 6-pin dip zero-cross phototriac driver optocoupler (600v peak) MOC3061-M moc3062-m moc3063-m moc3162-m moc3163-m note all dimensions are in inches (millimeters) pa ck ag e dimensions (through hole) pa ck ag e dimensions (surface mount) pa ck ag e dimensions (0.4 lead spacing) recommended pad layout for surface mount leadform 0.350 (8.89) 0.320 (8.13) 0.260 (6.60) 0.240 (6.10) 0.320 (8.13) 0.070 (1.77) 0.040 (1.02) 0.014 (0.36) 0.010 (0.25) 0.200 (5.08) 0.115 (2.93) 0.100 (2.54) 0.015 (0.38) 0.020 (0.50) 0.016 (0.41) 0.100 (2.54) 15 0.012 (0.30) 0.350 (8.89) 0.320 (8.13) 0.260 (6.60) 0.240 (6.10) 0.390 (9.90) 0.332 (8.43) 0.070 (1.77) 0.040 (1.02) 0.014 (0.36) 0.010 (0.25) 0.320 (8.13) 0.035 (0.88) 0.012 (0.30) 0.012 (0.30) 0.008 (0.20) 0.200 (5.08) 0.115 (2.93) 0.025 (0.63) 0.020 (0.51) 0.020 (0.50) 0.016 (0.41) 0.100 [2.54] 0.350 (8.89) 0.320 (8.13) 0.260 (6.60) 0.240 (6.10) 0.070 (1.77) 0.040 (1.02) 0.014 (0.36) 0.010 (0.25) 0.200 (5.08) 0.115 (2.93) 0.020 (0.50) 0.016 (0.41) 0.100 [2.54] 0.100 (2.54) 0.015 (0.38) 0.012 (0.30) 0.008 (0.21) 0.425 (10.80) 0.400 (10.16) 0.070 ( 1.78 ) 0.060 ( 1.52 ) 0.030 ( 0.76 ) 0.100 ( 2.54 ) 0.305 ( 7.75 ) 0.425 ( 10.79 )
6/15/05 p age 8 of 10 ?2005 fairchild semiconductor corporation 6-pin dip zero-cross phototriac driver optocoupler (600v peak) MOC3061-M moc3062-m moc3063-m moc3162-m moc3163-m ordering information marking information option order entry identi?r description ss surface mount lead bend sr2 sr2 surface mount; tape and reel tt 0.4" lead spacing vv vde 0884 tv tv vde 0884, 0.4" lead spacing sv sv vde 0884, surface mount sr2v sr2v vde 0884, surface mount, tape & reel moc3061 v x yy q 1 2 6 4 3 5 *note ?parts that do not have the ? option (see de?ition 3 above) that are marked with date code ?25 or earlier are marked in portrait format. de?itions 1f airchild logo 2d e vice number 3 vde mark (note: only appears on parts ordered with vde option ?see order entry table) 4 one digit year code, e.g., ? 5t wo digit work week ranging from ?1 to ?3 6 assembly package code
6/15/05 p age 9 of 10 ?2005 fairchild semiconductor corporation 6-pin dip zero-cross phototriac driver optocoupler (600v peak) MOC3061-M moc3062-m moc3063-m moc3162-m moc3163-m note all dimensions are in inches (millimeters) re?w pro?e (white package, -m suf?) carrier tape specifications 4.0 0.1 1.5 min user direction of feed 2.0 0.05 1.75 0.10 11.5 1.0 24.0 0.3 12.0 0.1 0.30 0.05 21.0 0.1 4.5 0.20 0.1 max 10.1 0.20 9.1 0.20 1.5 0.1/-0 300 280 260 240 220 200 180 160 140 120 100 80 60 40 20 0 c time (s) 0 60 180 120 270 260 c >245 c = 42 sec time above 183 c = 90 sec 360 1.822 c/sec ramp up rate 33 sec
life support policy fairchild? products are not authorized for use as critical components in life support devices or systems without the express written approval of the president of fairchild semiconductor corporation. as used herein: 1. life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. a critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. disclaimer fairchild semiconductor reserves the right to make changes without further notice to any products herein to improve reliability, function or design. fairchild does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent rights, nor the rights of others. 6/15/05 p age 10 of 10 ?2005 fairchild semiconductor corporation 6-pin dip zero-cross phototriac driver optocoupler (600v peak) MOC3061-M moc3062-m moc3063-m moc3162-m moc3163-m
|
